Humidity

Whole-House Humidifier Cost and Installation: What to Expect

Unit prices, what a contractor actually does, typical installed totals and the yearly cost of keeping it running.

By ClariSelect Editorial · Updated October 2026

The short answer

Expect roughly $500 to $1,000 installed for a bypass humidifier, $700 to $1,300 for a fan-powered model and $1,500 to $3,000 for a steam unit, depending on your ductwork, plumbing access and local labor rates. The unit itself is about a third to a half of that. After installation, budget for one water panel per heating season, about $30 to $60 for the Aprilaire panels we list.

What the humidifier itself costs

Furnace-mounted humidifiers come in three types, and the type drives most of the price. These are current listed prices for the Aprilaire models in our catalog, the most widely installed brand in the US.

Listed unit prices for common whole-house humidifiers
ModelTypeMaker's outputListed price
Aprilaire 500Bypass12 gallons/day$284.99
Aprilaire 600Bypass17 gallons/day$339.99
Aprilaire 700Fan-powered18 gallons/day$524.99
Aprilaire 800Steamsee maker's chart$1,119.99

Contractors often supply the unit themselves at a markup, so ask whether the quote includes the humidifier and which model. The Aprilaire 600 and 700 are the usual choices for typical homes; the 500 suits smaller homes and tight furnace closets.

What installation involves

  1. Mounting: cutting an opening in the supply or return plenum and fixing the unit. Bypass models also need a short round duct between supply and return.
  2. Water supply: a small line from the nearest cold (or, for some models, hot) water pipe with a saddle or tee valve.
  3. Drain: evaporative units send unused water to a drain; with no floor drain nearby, a condensate pump adds cost.
  4. Wiring: low-voltage wiring to the furnace and a humidistat or compatible thermostat. Steam units usually need their own electrical circuit.
  5. Setup: setting the target humidity, often with an outdoor temperature sensor so the system lowers humidity on cold nights to prevent window condensation.

A straightforward bypass install takes a contractor two to four hours. Costs climb when the furnace is in a tight closet, the water line or drain is far away, or a steam unit needs a new circuit run from the panel.

Typical installed totals

Typical installed cost ranges
TypeUnitLabor and partsTypical total
Bypass$230 to $340$250 to $650$500 to $1,000
Fan-powered$480 to $525$250 to $750$700 to $1,300
Steam$1,100 and up$400 to $1,900 (often including electrical)$1,500 to $3,000
How to use these numbersThese ranges are typical for US contractors and vary widely by region. Get two or three written quotes that name the model, the humidistat and whether a drain pump or new circuit is included.

Which type is worth it

  • Bypass: the cheapest to buy and run. It uses the furnace blower and needs space for the bypass duct. Right for most gas-furnace homes.
  • Fan-powered: has its own fan, so it needs no bypass duct and delivers more moisture. Choose it for larger homes or where there is no room for the duct.
  • Steam: boils water, so it adds moisture even when the furnace is not heating and does not depend on warm supply air. The usual choice for heat pumps, very dry climates and large homes.

If you have a heat pump, an evaporative unit will underperform because heat-pump supply air is cooler than furnace air. See bypass vs fan-powered humidifiers for a deeper comparison.

Yearly running costs

  • Water panel: replace one each heating season, more often with hard water. The Aprilaire 35 panel (for the 600 and 700 series) is listed at $59.15, the Aprilaire 10 (for the 500 series) at $45.17, and the Aprilaire 12 (for the 400) at $28.13.
  • Steam canister: steam units use a replaceable canister instead; the Aprilaire 80 canister is listed at $114.05, and hard water shortens its life.
  • Electricity: bypass units draw almost nothing beyond the furnace blower; steam units draw substantially more while running.
  • Water: evaporative units send some water down the drain while running; steam units waste much less.

Our water panel maintenance guide shows how to change the panel yourself in about 15 minutes.

Products mentioned

Questions readers ask

How much does it cost to install a whole-house humidifier?
Typically $500 to $1,000 for a bypass model, $700 to $1,300 for a fan-powered model and $1,500 to $3,000 for a steam unit, including the unit. Prices vary by region and installation difficulty.
Can I install a whole-house humidifier myself?
It is possible if you are comfortable cutting ductwork, tapping a water line and wiring to the furnace control board, but most homeowners hire a heating contractor. A poor install can leak into the furnace or flood the floor.
Does a whole-house humidifier work with a heat pump?
Yes, but evaporative models put out less moisture because heat-pump air is cooler. Steam humidifiers work independently of supply-air temperature and suit heat pumps best.
How often do I change the water panel?
At least once each heating season, and more often with hard water or if the panel is stiff with scale before spring.
Is a whole-house humidifier worth it?
If you are running two or more room humidifiers all winter, usually yes: one furnace unit covers every room, needs less daily attention and costs little to run after installation.